Kitchen cabinets are the most pivotal element of every kitchen. You need to keep them well maintained and upgraded. But any small wear and tear can cause them damage. So, there are multiple methods to give your cabinets a finished and graceful look. Just go by installing crown molding along top edges.

Crown molding can hide all the dark and dirty open soffits on wall cabinets. This gives them a very even and fine look. The crown molding is not just fixed into wall cabinets. So, simply work with wooden nailing strips which makes the overall process so simple. These strips enhance your skill and will accurately position the crown molding.

 Moreover, you must prefer J&K cabinets in your kitchen. Let’s go down to see through the whole procedure.

List of content:

1. Materials Required
2. Tools / Gadgets
3. Do Nailing Strip Measurement
4. Make Sure To Measure Lower Edge Of Crown Molding
5. Chop Down The Nailing Strips
6. Keep The Nailing Strips In Position
7. Nailing Strip Security
8. Cut And Attach The Front Part Of Crown Molding
9. Cut And Attach The Side Parts Of Crown Molding
10. Match The Corners
11. Paint And Finish the Crown Molding Surface
12. Where To Buy Affordable J&K Cabinets?
13. Conclusion

Materials Required:

• Lumber strips
• Crown molding
• Primer
• Interior paint
• Wood putty

Tools / Gadgets:

• Electric miter saw
• Electric nail gun
• Measurement tape
• 6-foot ladder
• Sheet plastic or masking film
• Painters tape
• Fine grit sandpaper
• Speed square
• Putty knife
• Paintbrush

Do Nailing Strip Measurement:

You can measure the width, depth, and length of wall cabinets with measuring tape. It’s important to measure down the width, depth. As crown molding will be wrapped around the cabinets. 

Make Sure To Measure Lower Edge Of Crown Molding:

If you want a sleek outlook, then cover the bottom of the cabinet with crown molding. So, fix the nailing strips on all sides by thickness on the lower edge of crown molding. Use a measuring tape to check thickness. Thus, for standard crown molding, the thickness is around ⅛ inches.

Chop Down The Nailing Strips:

Now cut the nailing strips of the cabinet perimeter size. So the front portion should be as long as the width of the cabinet. Like a cabinet that is 36 inches in width. Then the front strip will be 35 ¾ inches. However, the length of each side strip will be done by wall cabinet depth. 

Keep The Nailing Strips In Position:

So, now place the nailing strip on the front of the cabinets. And set them by the thickness of crown molding lower edge. It is also helpful to make setbacks with crown molding rather than a measuring tape.

Nailing Strip Security:

It’s important to check for safety. So, double-check your measurements and placements. Make sure to have accurate placements. Always use the nail to nail the strips on the top of cabinets.

Cut And Attach The Front Part Of Crown Molding:

It’s time to measure down and mark the front sections of crown molding to the cabinet width. Now set the miter saw at 45 degrees angle. Thus, place the crown molding upside down at a 45-degree angle against the saw fence. 

Chop down at one point. Then move the crown molding to the next point. Thus, place the saw at a 45-degree angle to chop the second cut. 

Cut And Attach The Side Parts Of Crown Molding:

Now the two side sections of crown molding you need to cut them at one angle. Thus, the other side can be cut at a straight 90-degree angle. The left section of crown molding at 45 degrees is cut on one side. So, the crown molding at the front 45 degrees left side. Now repeat the same for the right side. 

Match The Corners:

Simply drive one brad through one board to join the other. So, let them match together. Now repeat for the right side too.

Paint And Finish the Crown Molding Surface:

Cover the cabinets with sheet or masking film and fix it with painter tape. So, depending on nail hole size. You must fill them with wood putty and leave them unfilled. Thus, apply interior paint to fill the small holes with nail guns. Now coat them with two layers of paint. And let the paint settle for four hours before removing plastic. 

Where To Buy Affordable J&K Cabinets?

There are a lot of places which sell kitchen cabinets. But you really need to hunt down one most affordable and high-quality cabinet. So, here is one incredible shop, the Kitchen Design Gallery in the USA. From there you can buy premium quality, trendy styles, durable material, and affordable J & K cabinets easily.

Conclusion:

In conclusion, crown molding is the method to make your cabinets more attractive. Although this process is quite hectic. But by following the above instructive guide you can simply crown mold the cabinet by easy DIY steps. So, just gather material, tools, and instruction guides together. And follow the steps below. Do all the measurements accurately and fix the crown molding on the cabinets. Lastly, always prefer to buy J&K style cabinets to make your kitchen look so attractive and highly functional.